Sim2 M.150S User Manual

Browse online or download User Manual for Projectors Sim2 M.150S. M.150 RS-232 Control 1.0 [en]

  • Download
  • Add to my manuals
  • Print
  • Page
    / 16
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
SIM2 Multimedia
M.150
RS-232 Control
Rev. 1.0 (20 January 2012)
Page view 0
1 2 3 4 5 6 ... 15 16

Summary of Contents

Page 1 - RS-232 Control

SIM2 MultimediaM.150RS-232 ControlRev. 1.0 (20 January 2012)

Page 2 - Contents

OverscanAction Command ResponseIncrement BE EF 1A 0C 00 91 52 04 00 02 00 00 00 00 00 00 00 00 00 OK 20 XX 00Decrement BE EF 1A 0C 00 54 03 04 00 03 0

Page 3 - 1 Introduction

MemoriesAction Command ResponseMemory 1 Recall BE EF 02 06 00 A8 F2 A1 01 00 00 00 00 OK 06Memory 2 Recall BE EF 02 06 00 9B F2 A2 01 00 00 00 00 Erro

Page 4 - 1.2 Execution of the command

Signal StatusWhen then unit is On, the returned packet (25 byte long) is described in the following table:1E BE EF 10 11 00 .. .. 01 01 00 01 01 15 01

Page 5 - 2 Commands

• 3 Error bytes (bytes 18–20) that signal errors in the processing of the command• 5 Data bytes (bytes 21–22, 24, 25–26) that contain the requested da

Page 6 - 2.2 Operation Commands

3 ExamplesSend the simulated ‘SWITCH ON FROM STANDBY’ Remote Control keycodeRemote Control allows Switching on from Standby via the key ‘0’.Send the c

Page 7

THIS PAGE LEFT BLANK INTENTIONALLY15

Page 8

SIM2 Multimedia S.p.A.Viale Lino Zanussi, 1133170 Pordenone — ItalyPhone: +39.0434383256Fax: +39.0434383260Email: [email protected] USA1010

Page 9

ContentsContents 21 Introduction 31.1 Setting up the RS-232C Serial connection . . . . . . . . . . . . . . . . . . . . . . . . . . . 31.2 Execution of

Page 10

1 IntroductionThis document describes how to interface the M.150 projector with a Home Theater control system (or aPC) over a direct serial connection

Page 11 - 2.3 Status Commands

1.2 Execution of the commandCommand execution time may vary from 0.1 to 2.0 seconds, depending on the operation that have beenrequested.If the project

Page 12 - Light Source Status

2 CommandsIn this section, serial commands (and respective responses) are listed. Commands (and responses) are seriesof bytes (numbers holding values

Page 13

Commands 1–9 perform different actions depending on the projector status:Status Command ActionStandby 0 switches the unit on and selects the last input

Page 14 - 3 Examples

BrightnessAction Command ResponseIncrement BE EF 1A 0C 00 5E A3 00 00 02 00 00 00 00 00 00 00 00 00 OK 20 XX 00Decrement BE EF 1A 0C 00 9B F2 00 00 03

Page 15

PureMotion (2D only)Action Command ResponseSet Off BE EF 1A 0C 00 83 2B 5E 00 00 00 00 00 00 00 00 00 00 00 OK 20 XX 00Set Low BE EF 1A 0C 00 4F EA 5E

Page 16

Color ManagementPrimariesAction Command ResponseSet Native BE EF 1A 0C 00 68 FE 41 00 00 00 00 00 00 00 00 00 00 00 OK 20 XX 00Set Cinema BE EF 1A 0C

Comments to this Manuals

No comments