Sim2 Domino 45 User Manual download pdf (Page 61)

that you leave it to finish. If really necessary you can interrupt tuning

at any time by pressing the TV key [21].

When the Autostore procedure finishes, if you wish to edit the chan-

nel table or change programme numbers, proceed as instructed in

section 4.6.3 Editing and reorganising the channel table.

4.6.2 Tuning in and programming channels

manually

If you wish to tune in and programme channels manually (one at a

time), proceed as instructed below:

-01- Press the yellow key [4] to display the Main Settings menu.

-02- Scroll through the menu to “Installation”. Select and confirm

“Installation”.

-03- Select “System” then select the ‘transmission standard’ used

for television broadcasts in your country. Select PAL-BG for Italian

and German channels, etc.. Select SECAM-L for French channels.

Select PAL-I for British channels. Select NTSC etc. as and when

relevant. If you are in doubt as to your national standard, select

“Auto” to allow the television to recognise transmission standards

automatically while tuning in. (IMPORTANT! The only valid option for

French channels is SECAM-L.) In some cases it may not be suffi-

cient to select “Auto” and you may have to specify a transmission

standard manually as instructed above.

-04- Scroll to “Channel Type”, select “CH” if you wish to tune the

broadcasted channels received with a conventional antenna, or “S”

if you wish to tune the channels diffused by cable (only possible if

you are connected to a cable channel service provider).

-05- Scroll through the menu to “Prog. Number” and use the

numeric keypad [2] on the remote control to enter the programme

number (using two digits, from 01 to 99) in which you wish to store

the channel.

NOTE: We recommend that you leave programme number ‘0’ free. If

you connect a video recorder to the television’s antenna connector

[B] (see section 4.5 SELECTING THE AUDIO-VIDEO SOURCE), pro-

gramme number ‘0’ is automatically assigned to the signal from the

video recorder.

-06- Scroll through the menu to “AFC” and select “On”. This swit-

ches on automatic frequency control, ensuring that the strongest

signal for the channel is tuned in.

-07- Scroll through the menu to “Channel” and use the remote

control’s numeric keypad [2] to enter the number of the channel (in

two digits) that you wish to tune in. If you do not know the channel

number, press and hold key [23] to start searching automatically for

the next channel after that currently being viewed, or press key [24]

to search for the previous channel. In this way the television tunes in

the first channel it finds. If the quality of reception is not satisfactory,

proceed as follows to adjust reception.

-08- Scroll to “Fine Tune” in the Installation sub-menu, and move

the slider control until you obtain interference-free image and sound.

4.6 TUNING IN AND

PROGRAMMING (TV)

This section explains how to tune in to the various channels recei-

ved by your antenna. You can tune in and store channels in program

numbers in either of two ways: MANUALLY or AUTOMATICALLY.

To ensure quick and easy tuning of all the channels available in your

area, we recommend that you follow the automatic tuning procedure

unless you are thoroughly conversant with manual tuning.

4.6.1 Tuning in and programming channels

automatically

This procedure uses ATS (the Automatic Tuning System) to tune in

all the channels received from local transmitters, and to store them

in the program numbers in memory. Before you start, check that the

factory set transmission standard corresponds to that used in your

country. (To check and change the transmission standard see sec-

tion 4.6.2 Tuning in and programming channels manually, step -03-.)

Once you have checked the transmission standard, proceed as fol-

lows.

-01- Press the yellow key [4] to display the Main Settings menu.

-02- Scroll through the menu to “Setup”. Select and confirm

“Setup”.

-03- Select the “Country” option and select the country in which

you live. (Countries are identified by their international codes: A, B,

CH, D, F, UK, I, NL, and E and “_ _” for all other countries.) By

selecting your country, you enable the ATS tuning system to auto-

matically associate the most important national channels with the

first available programme numbers. For example, if you select “I” for

Italy, the system will automatically store RAI 1, RAI 2, RAI 3 etc, in

the first programme numbers.

-04- Select “Ch. Table” and select the area of Europe in which

you live. The available options are “Italy”, “France”, “OIRT” (East

European countries) and “Europe” (other European countries). This

selection enables the tuning system to rapidly and automatically

identify the channels listed in the ‘Radio Frequencies Tables” publis-

hed by each European country.

-05- Select and confirm “Autostore”. The Autostore menu

appears with the “Start” option pre-selected. If you do not wish to

proceed, select and confirm “Cancel” instead.

-06- If you wish to start automatic channel tuning, simply confirm

“Start”. The Busy... screen appears and the system begins automa-

tic tuning. Each channel tuned in is memorised in the channel list

and automatically associated with a programme number. As each

channel is tuned, in the message “Found” appears alongside the

corresponding programme number.

When the channel list is complete, the Busy... screen disappears

and the television displays the image of whatever channel has been

assigned to programme 1.

NOTE: Once the Autostore function has started, we recommend

1 2 ... 56 57 58 59 60 61 62 63 64 65 66 ... 79 80

Comments to this Manuals

No comments

Sim2 Domino 45 User Manual Page 61

Comments to this Manuals

Related products and manuals for Projectors Sim2 Domino 45